If you’ve ever held a smartphone, a smartwatch, or even a modern medical device like a portable glucose monitor in your hand, chances are you were interacting with a mixed technology PCB assembly. As a PCB assembly supplier who’s spent the last 12 years walking clients through everything from prototype builds to high-volume production runs, I’ve seen firsthand how this underrated process turns just boards and parts into the workhorses of the electronics world. Let’s break down what mixed technology PCB assembly actually is, why it matters, and how it can make your next product stand out in a crowded market. PCB Assembly

First, let’s start with the basics to set a foundation. Most PCB assemblies fall into two broad categories: surface-mount technology (SMT) and through-hole technology (THT). SMT components are small, compact parts (think resistors, capacitors, microchips) that mount directly to the surface of a printed circuit board. They’re ideal for dense, high-frequency designs where space is at a premium—like the motherboard of your laptop or the tiny circuit inside wireless earbuds. Through-hole technology, on the other hand, uses larger pins or leads that insert through drilled holes in the PCB, then get soldered on the opposite side. These parts are bulkier, more mechanically robust, and better suited for components that need to handle physical stress or high power, like connectors, switches, or power transistors.
Mixed technology PCB assembly is exactly what it sounds like: a manufacturing process that combines both SMT and THT components on a single board. It’s not a new concept, but it’s become infinitely more important as products evolve to balance size, performance, and durability. Ten years ago, I might have only recommended mixed technology assemblies for niche industrial or automotive products, but today, nearly every product in development that bridges high performance and real-world use cases benefits from it.
Let’s get into why you’d choose mixed technology over a pure SMT or pure THT build. Suppose you’re designing a handheld industrial sensor that needs to fit in the palm of a worker’s hand, handle extreme vibration on a construction site, and run on low power for 10,000 hours. If you go pure SMT, you can cram all the tiny processing and communication chips onto the board, but the bulky power connector or the vibration-resistant fuse you need for durability would be too big to mount on the surface—or if you force an SMT version of that connector, it might crack or come loose after a few months of use. Go pure THT, and your board will be too large, heavy, and expensive to mass-produce, because through-hole components cost more and take longer to place by hand for high volumes. Mixed technology solves that: you place all the small, high-density SMT parts for processing and communication, then insert THT components for the high-stress parts like connectors and fuses, combining the best of both worlds.
Another example: medical devices. A portable ECG monitor needs a tiny, precise microprocessor to analyze heart data (perfect for SMT) and a large, durable battery connector or a power input that can withstand being plugged in and out hundreds of times a day (needs THT). You can’t get that balance from one technology alone. I worked with a client a few years back who was developing a at-home blood pressure monitor; their first pure SMT prototype had a habit of losing connection to its charger because the micro-USB port was too small and flimsy. By switching to a mixed technology assembly, we swapped in a through-hole USB port and kept the tiny SMT pressure sensor and display drivers, cutting their device’s charge failure rate by 82% and keeping the form factor they’d designed for. The client went on to sell over 2 million units, all built on mixed technology boards we assembled.
Now, the most important part: how mixed technology PCB assembly actually works, because it’s not just “placing SMT and THT parts anywhere.” A well-executed mixed build is all about sequence and precision, and that’s where a good assembly supplier adds real value. Let’s walk through the typical production flow we use in our facility, step by step.
First, we start with the PCB design files and bill of materials (BOM), which we review with our engineers to confirm that the mixed technology layout is feasible. Not all PCBs are designed for both SMT and THT, so this first check is critical to avoid costly reworks later. For example, we need to make sure there’s enough space around through-hole pad stacks for the SMT stencil, and that high-power THT components don’t interfere with sensitive SMT signals that could cause noise.
Next comes the solder paste stencil printing, the first SMT-specific step. We apply a thin, precise layer of solder paste only to the pads where SMT components will go, using a laser-cut stencil that matches the exact footprint of each part. Then, we use pick-and-place machines—high-speed, automated robots that can place thousands of tiny SMT parts per hour with micron-level accuracy—to mount all the surface-mount resistors, capacitors, ICs, and passives. Once all SMT parts are placed, we run the board through a reflow oven: a controlled temperature chamber that melts the solder paste, fusing the SMT parts to the board without damaging the sensitive components. This is a key step because we can’t send through-hole parts through the same reflow oven at the same time—many THT components, like connectors or large power resistors, can’t handle the high temperatures needed for reflow, so they have to be soldered separately.
After the SMT side is complete, we flip the board over and prepare for through-hole assembly. This can be done two ways, depending on the volume and part size: automated through-hole insertion or hand soldering for low-volume prototypes. For high-volume production, we use automated insertion machines that pick up THT components, align their leads with the drilled holes in the PCB, and push them through, trimming the excess lead length automatically. For prototypes, small runs, or very large THT parts that can’t be handled by automation, our skilled technicians do hand insertion, which is more flexible and avoids damage to expensive parts.
Once all THT components are in place, we move to wave soldering or selective soldering. Wave soldering involves passing the bottom of the board over a moving wave of molten solder that fills the holes and solders the THT leads to the board. We only use this method for boards where the SMT components on the opposite side are rated to handle the contact heat, which is why we time this step right after reflow and before any sensitive parts are damaged. For more sensitive SMT parts that can’t handle wave soldering heat, we use selective soldering: a precision robotic system that applies solder only to the specific THT pads we target, with minimal heat exposure to the surrounding SMT components. This is a more expensive process, but it’s non-negotiable for high-frequency or medical devices where signal integrity is critical.
After soldering, we run a series of quality checks, which are even more important for mixed technology assemblies because there are two different soldering processes and more points for potential defects. We use automated optical inspection (AOI) to check for bad solder joints, misplaced parts, or missed components on both SMT and THT sides, then functional testing to make sure every circuit works as intended. For high-stress applications like automotive or industrial, we also do vibration testing, thermal cycling, and x-ray inspection for hidden solder joints that AOI can’t see.
Now, let’s talk about common mistakes I see clients make when they’re designing mixed technology PCBs, because these are the issues that turn a promising design into a production headache. The first mistake is thinking all THT components can be handled the same way. Large power components like high-current transistors might be fine for wave soldering, but small, delicate through-hole parts like RF connectors or sensor pins will break if exposed to that level of heat. Another mistake is placing THT components too close to SMT components that are sensitive to mechanical or thermal stress. For example, a through-hole connector next to a tiny SMT microchip can create stress on the board when the connector is mated, leading to cracked solder joints on the chip over time.
The second big mistake is not accounting for lead time and cost when designing for mixed technology. THT parts are often more expensive than SMT equivalents, and mixed technology assemblies take 15-20% longer to produce than pure SMT builds because of the extra soldering and inspection steps. A lot of new designers skip this detail and end up with a product that’s late to market or over budget. That’s why working with an assembly supplier early in the design process is so valuable—we can catch these issues before you invest in prototype spins and tooling.
I also want to bust a common myth: some people think mixed technology is an outdated process, that SMT has gotten so small and reliable that you don’t need through-hole parts anymore. That’s simply not true. The smallest SMT connectors max out at about 0.4mm pitch, which is too small to handle high current or frequent mating cycles without failing. Even the most advanced surface-mount power components can’t match the current handling of through-hole parts for industrial or automotive use. For products that need to last 5 or 10 years in harsh conditions, mixed technology is still the most reliable, cost-effective solution.
One of the most satisfying parts of my job is seeing how mixed technology assemblies enable products that improve people’s lives. Last year, we built a batch of mixed technology PCBs for a company making portable defibrillators for rural clinics in low-income countries. Those boards combined tiny SMT microprocessors that run the defibrillation algorithm, with through-hole battery terminals and high-voltage output connectors that could withstand rough handling during transport and use. Without mixed technology, those defibrillators would have been either too big to carry into remote villages or too fragile to work when you need them most.
If you’re working on a new product, whether it’s a consumer gadget, an industrial sensor, a medical device, or an automotive component, mixed technology PCB assembly is almost certainly a consideration. The key is to partner with an experienced supplier who can walk you through the trade-offs between size, durability, cost, and lead time, and who has the equipment and expertise to execute your design correctly.
At the end of the day, mixed technology isn’t just about combining two manufacturing processes—it’s about giving designers the flexibility to build exactly what their product needs, without compromising on performance or reliability. A poor mixed tech assembly can be slow, expensive, and full of defects, but a well-executed one is the foundation of a product that stands the test of time.

If you’re ready to start a project, or you’re looking to improve an existing mixed technology PCB assembly, I encourage you to reach out to our team to discuss your requirements. We’ll walk through your design, answer any questions you have about the process, and help you find the best solution for your production goals.
LED Light References:
1.IPC-2221, Generic Standard on Printed Board Design
2. IPC-A-610, Acceptability of Electronic Assemblies
3. “Surface Mount Technology vs. Through-Hole Technology: Advantages and Disadvantages,” Circuit Assembly Magazine, 2022
4. Automotive Industry Action Group (AIAG), Mixed Technology Assembly Best Practices, 2021
5. “Trends in Mixed Technology PCB Assembly for Medical Devices,” Medical Design and Outsourcing, 2023
WCN OPTO Group Co., Limited
WCN OPTO Group Co., Limited is one of the most experienced pcb assembly manufacturers and suppliers in China, also supports customized service. We warmly welcome you to wholesale advanced pcb assembly at competitive price from our factory. If you have any enquiry about pricelist, please feel free to email us.
Address: Buildings 1 and 2, No. 13, Songnan Road, Sino-Korea Industrial Park, Zhongkai High tech Zone, Huizhou, Guangdong,China
E-mail: williamzhang@wcnopto.com
WebSite: https://www.wcnopto.com/