If you’ve ever wondered how the tough, heat-resistant steel that makes die-casting molds, forging dies, and hot extrusion tools ends up in the hands of manufacturers, you’re not alone. As a JIS hot work tool steel supplier, I get this question all the time—from small machine shops just getting started to big automotive parts makers upgrading their production lines. Today, I’m breaking down exactly what goes into machining JIS hot work tool steel, from raw ingot to finished part, no jargon overload, just the real process we use every day. JIS Hot Work Tool Steel

First, let’s get one thing straight: JIS hot work tool steel isn’t your average carbon steel. It’s made to handle extreme heat—like 500°C and up—without softening, cracking, or wearing out fast. That’s why it’s the go-to for tools that punch, shape, and mold hot metal. But all that strength comes with a catch: it’s way harder to machine than regular steel, so you can’t just run it through a mill like you would with mild steel. We’ve spent years tweaking our processes to make machining JIS steel efficient, so I’ll walk you through each step the way our shop foreman would explain it, straight from the floor.
Step 1: Pre-Machining Prep—You Can’t Skip the Heat Treatment (Trust Me)
Wait, heat treatment is part of machining? Hear me out. Before you even touch a cutting tool, JIS hot work tool steel comes from the mill in a “pre-hardened” state usually around 30-35 HRC. But if you’re making something like a die that has to hold tight shapes for thousands of cycles, you’ll need to do a secondary heat treat: austenitizing, quenching, and tempering to get it up to 48-52 HRC, sometimes higher for really demanding jobs.
Here’s the mistake a lot of new machinists make: they machine the steel first, then heat treat. Big no-no. Heat treatment causes distortion—like, up to 0.5mm on a 100mm part if you mess it up. If you machine a part to tight tolerances first, it’ll warp when you heat treat, and you’re left with scrap. Our process is: machine the pre-hardened steel to within 0.2mm of final size, heat treat it, then do a light finish pass to fix any distortion. That saves so much time on rework, which is why our customers keep coming back.
Also, we always stress stress-relieving before machining if the steel has been sitting in inventory for more than a month. Hot work tool steel is hard, and leftover stresses from forging or rolling can cause it to crack mid-machining. A 2-hour soak at 600°C in our furnace gets rid of that, no surprises on the mill.
Step 2: Choosing the Right Cutting Tools—This Is Non-Negotiable
I can’t tell you how many times a customer has called us saying “your JIS steel is impossible to machine!” only to find they’re using a generic carbide insert made for mild steel. Let’s set the record: JIS hot work tool steel needs specific cutting tools. We use two main types: coated carbide and cubic boron nitride (CBN) tools.
For roughing passes—where you’re removing big chunks of material fast—coated carbide is perfect. We use TiAlN (titanium aluminum nitride) coated inserts, not the old TiN ones. TiAlN can handle the heat from the cutting edge way better, so it doesn’t wear out after a few parts. For finishing passes, CBN is the way to go. CBN is second only to diamond in hardness, so it cuts through the hardened steel without leaving a rough surface. It’s more expensive up front, but it lasts 10x longer than carbide, so it saves money in the long run.
Also, tool geometry matters. We use positive rake angles on our tools for roughing—they cut through the steel with less force, which reduces heat buildup. For finishing, slightly negative rake angles help with stability, so you get a smoother surface. Skip the negative rake for roughing, though—you’ll end up with way too much tool pressure, which will cause chipping.
Step 3: Machining Parameters—Speed, Feed, Depth, Don’t Guess
If you’re used to machining mild steel, you might be tempted to crank up the spindle speed and feed rate to get the job done fast. With JIS hot work tool steel, that’s a bad idea. Too fast, and the cutting edge overheats, wears out in minutes, and ruins your part. Too slow, and you’ll rub instead of cut, which also builds up heat and causes work hardening on the surface of the steel. That work hardening makes the steel even harder, so your next pass will be even harder on your tools.
We follow a rough formula we’ve tested over 10 years: for roughing, a spindle speed of 80-120 SFM (surface feet per minute) and a feed rate of 0.1-0.2 mm per tooth. For finishing, bump the speed up to 150-200 SFM, and drop the feed to 0.05-0.1 mm per tooth. Depth of cut? For roughing, 2-5 mm, but never more than the edge radius of your tool—otherwise, you’ll get tool chatter, which leaves a rippled surface. For finishing, a depth of 0.1-0.5 mm is ideal, since it’s light enough to avoid distortion but deep enough to smooth out any rough spots from roughing.
Also, coolant is non-negotiable. We use a high-pressure (1000 PSI) water-based synthetic coolant with a high concentration of lubricants. It not only keeps the cutting edge cool but also flushes out the chips, which is super important with JIS steel’s long, stringy chips. If the chips get stuck between the tool and the part, they’ll scratch the surface or break the tool. No coolant, no consistent machining—simple as that.
Step 4: Secondary Machining—Grinding, EDM, Polishing
Wait, we just talked about milling and turning, but a lot of JIS hot work tool steel parts need more than just cutting on a lathe or mill. Most die and mold parts need to be really smooth, like Ra 0.2 or better, which you can’t get with milling alone. So we do grinding next.
Surface grinding for flat parts, cylindrical grinding for rods or shafts, and tool grinding for complex shapes like punch tips. Grinding JIS steel is tricky because it’s hard—you need a grinding wheel made for hardened steel, like a vitrified bond alumina wheel or a diamond wheel. Soft wheels load up with steel chips, so we use harder wheels that can stay sharp longer. We also use coolant here too, to prevent heat buildup that can cause micro-cracks in the tool surface.
If you’re making a part with super complex cavities that can’t be milled—like a deep die cavity—EDM (electrical discharge machining) is the way to go. There are two types: wire EDM and sinker EDM. Wire EDM uses a thin brass wire to cut through the steel, no physical contact, so it can make super precise, smooth cuts. Sinker EDM uses an electrode shaped like the cavity, and sparks erode the steel to match the electrode shape. It’s slower than milling, but it’s perfect for parts where a mill can’t reach, like deep, narrow grooves.
Polishing is another big step for hot work tooling. Molds need a mirror-smooth surface to make finished parts with good surface finish. We do two types: mechanical polishing for general needs, and chemical polishing for ultra-smooth surfaces (Ra 0.05 or less). Chemical polishing is great for molds that shape plastic or light metals, where even a tiny rough spot would leave a mark on the finished part.
Step 5: Post-Machining Treatments—Final Touches That Make the Steel Last
Once the part is machined, ground, and polished, we do a couple of things to make it hold up longer. First, we do stress-relief annealing again after machining, just to make sure any leftover stresses from the process don’t cause it to crack when it’s in use. Then, if it’s a die that’s going to handle hot metal, we often do a nitride coating. Nitriding infuses nitrogen into the surface of the steel, making it harder (up to 1000 HV) and more wear-resistant, and it also gives it a little extra heat resistance. That way, your die can do 2x the number of cycles before needing to be replaced.
Wait, don’t skip the inspection step. We check every part for dimensional accuracy with a coordinate measuring machine (CMM), check the hardness with a portable hardness tester, and do a surface roughness test. JIS hot work tool steel is used for critical parts, so if a die fails, it can shut down a whole production line. We make sure every part leaves our facility meeting JIS standards, no exceptions.
Now, let’s talk about why our process works for JIS hot work tool steel specifically. JIS (Japanese Industrial Standards) defines the chemical composition for these steels—like SKD61, which is the most common hot work tool steel, has around 0.4% carbon, 5% chromium, and 2% molybdenum. That composition gives it the heat resistance, but it also makes it prone to work hardening and tool wear if you don’t adjust your machining process to match. A lot of general machinists don’t know the specific needs of JIS steel, which is why as a supplier, we don’t just sell you the steel—we help you machine it right, because we’ve been doing it for years.
I get it, machining JIS hot work tool steel can seem intimidating at first. But if you follow the steps: pre-machine prep to avoid distortion, use the right cutting tools, dial in your parameters, do the right secondary processes, and finish with the right coatings, it’s totally manageable. And the payoff is worth it—your tools will last longer, your parts will be more accurate, and you’ll save time and money on rework.

If you’re working on a project that needs JIS hot work tool steel, whether you’re making dies, tools, or custom components, we can help. We can guide you through the machining process, recommend the right grade of steel for your job, and make sure you get parts that fit your exact needs. Don’t waste time guessing on machining parameters or using the wrong tools—reach out to our team to start a conversation about your project, so we can get you the right steel and the support you need to make it work.
Hot Extrusion Die Steel References
- ASM International. (2020). Machining of Tool Steels. ASM Handbook, Volume 16: Machining.
- Japanese Industrial Standards Committee. (2018). JIS G 4404: Hot Work Tool Steels.
- Koike, J., & Sato, T. (2019). Optimization of Machining Parameters for JIS SKD61 Hot Work Tool Steel. Journal of Manufacturing Processes, Vol. 45, pp. 234-241.
- Dee, D. (2021). Tool Selection for Machining Hardened Tool Steels. Cutting Tool Engineering, Vol. 73, Issue 5.
Zhejiang Yiding New Materials Co., Ltd.
As one of the most professional jis hot work tool steel manufacturers and suppliers in China, our products have good reputation in the market. Please feel free to wholesale high quality jis hot work tool steel made in China here from our factory. Also, custom service is available.
Address: Xingwang Industrial Park, Huzhen Town, Jinyun County, Zhejiang Province, China
E-mail: jun.wang@ydmat.com
WebSite: https://www.ydmat.com/