Posted in

how to test the seal strength of a bagging and heat shrink machine package

Hey everyone, I’m Jake, part of the team here that builds bagging and heat shrink machines—so I get it, you’re not here for some stuffy whitepaper. You’re here because you just dropped thousands on a new shrink wrap or bagging line, and if your package seals fail mid-shipment, that’s a nightmare. Not just wasted product, but irate customers, extra shipping costs, and maybe even brand damage. I’ve seen it happen a dozen times, and the fix starts with actually testing your seal strength right, not just guessing. Bagging and Heat Shrink Machine

First off, let’s cut through the jargon: seal strength is just how hard you have to pull a sealed bag or shrink wrap seam before it breaks. But here’s the thing—testing it wrong is basically useless. I’ve had customers call me panicking because their seals failed, only to find out they tested them like they were squeezing a soda can, not simulating real world shipping. If you want actionable, real results, you gotta do it like the pros.

Let’s start with the basics: what kind of package are we even talking about? Because testing a poly bag for snack bars is way different than a heavy-duty shrink wrapped pallet of car parts. Same goes for heat shrink vs. bagging seals—shrink wrap usually has a thinner film, so you don’t need as much strength, but bagged products with sharp edges? You need way more pull force, no exceptions.

First up, the most straightforward test: the manual peel test. Wait, I know what you’re thinking—“Jake, that’s just yanking the seal open, right?” No, not the kind where you’re just pulling with your fingers. For a manual test, you need a pull tester. Yeah, the little bench-top ones we can even help you source if you don’t have one. Here’s the step-by-step: cut a test strip that’s at least 1 inch wide and 6 inches long, with the seal right in the middle. Clamp one end in the tester’s grip, the other end in the opposite grip, then pull at a constant speed—usually 12 inches per minute, that’s the industry standard for flexible packaging. The machine will tell you exactly how much force (in pounds or Newtons) it took to break the seal.

Now, what’s a good number? For most standard poly bags, you’re looking for at least 5 to 10 pounds per inch of seal width. For heat shrink film, that’s a little lower—3 to 7 pounds per inch, because shrink film is thinner. But here’s the catch: if the seal breaks along the seal line, that’s a pass. If it breaks in the film, that means you’re probably over-sealing, which wastes film and can weaken the seal over time (too much heat melts the film too much, making it brittle). I see this all the time—customers crank up the heat on their shrink machine because they think a stronger seal is better, but it backfires.

But wait, the manual pull test is lab-level, right? What if you’re on the production floor and you can’t wait for the lab results? There’s a quick field test we use with our operators all the time, no fancy gear needed. It’s called the “hand tug test,” and it’s super simple. After the machine seals a batch of test packages, take a random one, grab each end of the sealed seam, and yank as hard as you can with both hands. If it breaks on the seal, great. If it breaks in the film, that’s over-sealing. If it comes apart without much effort, that’s under-sealing. But here’s the rule for this test: you can’t use your whole body weight. Just your arm strength. Because if you yank too hard, you’ll break a good seal. We tell our operators to make it a tug equivalent to opening a tight jar. No more. That’s a good baseline for production checks.

But here’s the part most people miss—real world testing. Because a package might hold up in your lab, but get banged around in a truck, dropped, stacked on a pallet, and suddenly that 5-pound seal is a 3-pound seal. That’s why the drop test and stack test are non-negotiable, especially for products that ship far or get stacked.

The drop test: take 10 test packages that have been sealed on your machine, each with the same product inside (don’t do this empty—product weight changes how the seal holds). Drop them from 3 feet high, right onto the sealed seam first, because that’s the weakest point. Do it on hard surfaces, concrete, not carpet. After dropping, check each seal—if more than one comes apart, your seal strength is too low. For heavy items (over 50 pounds), you might need to drop from 4 or 5 feet. We had a customer shipping 70-pound shrink-wrapped ATV parts once, and they were dropping from 6 feet to simulate loading docks—turned out their original seal strength was only 4 pounds, they needed 8. Fixed it, zero failures after that.

Then the stack test: this mimics pallets being stacked on top of each other in a warehouse. Take a sealed package, put a weight on top of it—usually 2 to 3 times the total weight of the package. Leave it for 24 to 72 hours, then check the seal. If it’s intact, great. If it separates, you need a stronger seal. This is especially important for heat shrink pallets—if your shrink wrap is too thin, stacking pallets can make the wrap stretch and break at the seams. We had a customer who kept having broken shrink wraps on their 10-pallet stacks; once they did a 3x weight stack test, they realized their machine’s heat setting was too low, so the seal wasn’t bonding properly. Fixed that, no more broken pallets.

Wait, what about other factors that mess up seal strength? I’ve talked to so many customers who blame the machine, but it’s usually not the machine—it’s the film or the settings. Let’s break that down, because testing is useless if your settings are off. First, film thickness: a 2-mil film needs less force than a 4-mil film. If you’re testing a thin bag like a snack bag, don’t expect the same strength as a heavy-duty industrial bag. Second, heat settings: too low, and the seal doesn’t melt enough to bond, so it’s weak. Too high, and like I said earlier, the seal becomes brittle and breaks easy. We calibrate all our machines before we ship them, but every film is a little different—so you have to test your specific film and product. Third, dwell time: that’s how long the seal bar stays pressed on the bag. If dwell time is too short, the seal doesn’t fuse right, so it’s weak. Too long, and again, over-sealing.

Here’s a quick pro tip from our team: do a “batch test” instead of testing one package. Because one bad seal is usually a fluke, 3 bad seals out of 10 is a problem. We tell our customers to test 10 packages from every production run, not just the first one. If more than one fails, adjust the machine settings and test again. Also, test different parts of the run—sometimes the first few seals are different than the last few, because the machine warms up or cools down. I’ve seen customers test only the first 5 packages, then wonder why 10 in a 1000 fail.

Another thing: if you’re using a bagging machine with gusseted bags, the seal is different than flat bags. Gusseted bags have extra side folds, so the pull force is a little different. You need to make sure your test strip includes the gusset, not just a flat part. We have a little trick for that—when you cut the test strip, cut it at an angle so you capture the gusset edge. That gives you a more accurate reading of how the seal will hold with the bulging bag.

Wait, what about tamper-evident seals? A lot of our customers use those for food or pharmaceuticals, right? Tamper-evident seals have a specific strength requirement too—usually 8 to 12 pounds per inch, because you want them to break if someone tries to open them. So you have to adjust your test accordingly. If your tamper seal breaks in the film, that’s bad—you want it to break when someone tugs, not when someone tries to pry it open.

I know this sounds like a lot, but it’s all stuff you can do on your production floor, no fancy lab needed. Let’s recap the steps to make it simple: 1) Do a daily hand tug test with every batch, just to catch obvious issues. 2) Do a weekly pull test with a bench-top tester to get exact force numbers. 3) Do a monthly drop and stack test to simulate real shipping conditions. 4) Always test your specific film and product, not generic numbers.

If you’re still not sure where to start, or if you’re having seal failure issues that you can’t figure out, hit us up. We’re not just machine builders—we work with hundreds of customers every week to tweak settings, pick the right film, and make sure their seals hold up. We don’t do the stuffy sales pitch, we get what you need: less downtime, fewer failed packages, happy customers. We can walk you through test protocols, help you source the right pull tester, even come out and tune your machine if you’re having persistent issues.

Sewing Thread Packaging Machine References:

  1. Flexible Packaging Association. (2022). Seal Strength Testing Guidelines for Flexible Packaging.
  2. ASTM International. (2021). Standard Test Method for Seal Strength of Flexible Barrier Materials (ASTM F88-21).
  3. International Safe Transit Association. (2023). Test Procedures for Sealed Packages for Distribution.

Shanghai Peifu Packaging Machinery Co., Ltd.
We are one of the leading manufacturers and suppliers of bagging and heat shrink machine in China. With a professional production team, we are able to meet the needs of the majority of our customers. Please rest assured to buy customized bagging and heat shrink machine from our factory.
Address: No.1111, Xinlin Road, Fengxian District, Shanghai, China
E-mail: cathychensupplier@gmail.com
WebSite: https://www.peifupackaging.com/